Affordable Electricians in Cumming, GA

Upon arrival, I inspected a burnt breaker and a severely damaged electrical panel. The panel had suffered significant heat damage, prompting a recommendation for a complete replacement to ensure safety and reliability. The homeowner agreed to proceed with the replacement on the same day. I removed the damaged panel and installed a new one, reconnecting all existing circuits and labeling the breakers accordingly. Additionally, I installed a whole-home surge protector and extended an existing circuit to add an outlet in the mechanical room. All connections were checked, and the electrical system was verified to be operating correctly. The required electrical permit will be obtained for the panel replacement.

I received an urgent repair call regarding a burning odor and a warm wall plate near a living room 3-way switch. Upon arrival, I shut down the breaker and dismounted the switch plate. Inside the junction box, I discovered charred wiring due to loose back-stabbed wire terminations arc-heating under load. I carefully cut back the damaged conductors, then pigtailed fresh copper leads. Finally, I installed a heavy-duty screw-terminal 3-way switch inside a new enclosure to ensure safety and reliability.

I addressed an issue with a customer's commercial-grade treadmill in their home gym, which was causing standard 15-amp branch circuits to trip during workouts. To resolve this, I installed a dedicated 20-amp branch line directly from the main load center. This involved connecting a single-pole breaker and using heavy-duty 12-gauge cable to ensure it could handle the treadmill's peak power draw. After installation, I conducted thorough load tests to confirm the circuit's stability and reliability. The dedicated circuit successfully supported the treadmill's operation without any interruptions to the house's power supply.

We conducted an electrical safety inspection after a customer reported a buzzing main panel and flickering lights when the heat pump activated. Using a thermal diagnostic scan, we identified loose bus bar connections and heat-damaged breakers. We retorqued all main lug connections, replaced the faulty breakers, and balanced the leg loads to ensure a stable 240V supply, preparing the system for the colder months ahead.

Electrician came out to inspect and verify that the sauna wiring was installed correctly and safely. Electrician confirmed that the wiring was properly connected. Electrician also installed a new bidet outlet in the master bathroom, extending power from an existing GFCI-protected outlet. All work was completed and tested. Everything is functioning properly as intended.

Completed an electrical service visit to install two customer-supplied light fixtures, a countertop outlet, and a GFCI outlet in the garage. Mounted and connected both light fixtures, ensuring the wiring and connections were properly secured. Installed the countertop receptacle and added a GFCI outlet in the garage to provide ground-fault protection where needed. Tested the fixtures, switches, and outlets to verify proper operation and confirmed all newly installed components were functioning correctly upon completion.

Completed the installation of two customer-provided light fixtures, a new countertop receptacle, and a GFCI outlet in the garage. Removed existing fixture components as needed and connected the new lighting to the existing wiring. Installed and secured the countertop outlet and garage GFCI, ensuring the electrical connections were properly terminated. Tested both light fixtures for reliable operation and checked the receptacles, including the GFCI test and reset functions, to verify proper performance. All installed components were left operating as expected.

Completed an electrical service call to install a customer-supplied vanity light in the hallway bathroom. Removed the existing fixture as needed, inspected the mounting area and wiring, and connected the new light fixture to the existing electrical supply. Secured the fixture in place and verified that all wiring connections were properly installed. Tested the light switch and vanity light to confirm proper operation and ensure the fixture was functioning as expected before completing the service.

Completed electrical work to prepare two upstairs bedrooms for ceiling fan installation. Ran new electrical circuits from the existing switches to newly installed fan-rated electrical boxes centered in each bedroom. Secured and routed the wiring appropriately, made the necessary electrical connections, and ensured both fan boxes were properly mounted to support the new fixtures. Checked the completed wiring and connections to verify they were ready for the next stage of installation. Both bedrooms were left prepared for ceiling fan installation.

Completed electrical work involving the landscape lighting, bathroom circuit, and installation of a new GFCI outlet. Troubleshot the landscape lighting system and addressed the identified issues to restore proper operation. Worked on the bathroom circuit to ensure the wiring and connections were properly secured and functioning as intended. Installed a new GFCI receptacle, verified the electrical connections, and tested the outlet's ground-fault protection. Checked the completed work and confirmed the serviced components were operating properly.